Catalogue - Routing - Torquata Jointing Bits

Home / Routing / Torquata Jointing Bits

Products: 1 - 8 of 22

Page: | 1 , 2 , 3

Vertical Panel Raising Bit with Bead - VPR-93-H
This panel raiser has a diameter of only 26mm instead of up to 90mm for the usual horizontal style. Ideal for applications where there is a limitation on the size of the hole in your router plate. Profile is variable by raising or lowering bit to desired shape. Note: A fence is required and should be sufficiently high for adequate support of work piece. The cutter length is 41mm, cutter diamter is 25mm.

Birdsmouth Bits - BM-2222-H
Birdsmouth joints are a traditional joint used in making masts. These bits allow you to do this, but more interestingly, allow you to make multi-sided vessels. These bits will allow you to use timber up to 22.2mm (7/8in) thick for flush joints, but to make cylindrical pieces, use thicker material and then turn or plane down to the round shape. All bits have a 1/2in shank and should be used in a router table. Length of bit = 22.2mm, Diameter of bit 38.1 - 41.3mm

Qty:

$47.90 inc GST

BM-2222-H

Makes 16 Sided Vessels

Qty:

$47.90 inc GST

BM-2230-H

Makes 6 or 12 Sided Vessels

Qty:

$43.90 inc GST

BM-2245-H

Makes 8 Sided Vessels

Qty:

$139.70 inc GST

BM-SET

All 3 Bits BM-2222-H & BM-2230-H & BM-2245-H Together

Cove Back Cutting Panel Raising Bit - BCPR-80-BH
These bits are ideal for use where the panel timber is thicker than say 14 or 15mm (for example common 19mm stock) because it creates a “rebate” on the back so that the front raised panel does not protrude too far beyond the frame. Cutter depth = 33mm, Cutter height maximum = 25mm. 1/2in shank.

Chamfer Horizontal Panel Raising Bit - HPR-90-BH
Now you can make beautiful raised panel doors yourself using these this router bit in a router table. Panel raising bits cut the profile in the central panel to give the raised effect. Horizontal bits are larger and more difficult to operate but capable of doing curved profiles. NOTE 1: Due to the large diameter of some of these bits, extra care and lower rpm should be used. NOTE 2: Profiles variable by raising or lowering bits. 1/2in shank. Cutter depth = 37.5mm, Cutter length = 19mm

2-Piece Rail & Stile Set - SR-182-BH
Door making sets are avaliable either as a single bit which has interchangeable cutters or as a pair of fixed bits which are changed in the router to cut the two interlocking corner profiles. Using a pair of bits in the door making set has these advantages: 1. The spacing of the interlocking profiles is always exactly correct. With interchangable cutters minor spacial differences between the bearing and cutter plates are possible. 2. The thickness of material can be up to 25mm compared with 19mm
Read More...

One-Piece Stile & Rail Bit - SR-16-BH
Now you can make beautiful raised panel doors yourself using these router bits in a fixed router table that has a substantial fence. Simply run the bit at the profile that is shown in the image. Then, by loosening the top nut and changing the order of the pieces (in order from shank to tip), by putting the slot cutter on the bottom, bearing, then profile cutter, it will cut the opposing joint which will allow you to make a four-sided frame. 1/2in shank, suits timber 15-19mm thick.
Read More...

3-piece Doormaking Set - SRVO-3-BH
This top-value set has a pair of bits to make stiles & rails, the most common pair of rail & stile bits (SR-102-BH, plus the vertical panel raising bit (VPR-90-H). An economical way to buy and a safe way to store these valuable cutters in a sturdy and attractive wooden box.

2-Piece Doormaking Set - SRVO-2-BH
Buy the most popular ogee stile and rail bit (SR-10-BH) and vertical raised panal bit (VPR-90-H) as a complete set and not only save but get a sturdy storage box to protect you cutters well.

Products: 1 - 8 of 22

1 , 2 , 3

Home

Back

Timbecon PTY LTD
Pay by phone using Credit Card, Direct Debit, Cheque
Phone Sales: 1300 880 996 - 7.00am - 5.30pm (WST)

Site best viewed 1024x768 using Internet Explorer 6 or Mozilla Firefox 1.0, with cookies enabled and pop-up software disabled.

Problems with the site? Email: webmaster@timbecon.com.au