CMT Router Bits

Results 1 - 96 of 110 Show: Sort By:
  • 191 Series Solid Carbide Upcut Spiral Bits

    Sharp technology with a new twist

     

    A special super-micrograin carbide formulation was created to produce and hold a keen cutting edge. The new low-angle spiral is designed specifically to shear wood cleanly and provide efficient chip ejection. The tools run cooler and the edges last longer.

    Increased feed rate and improved cutting quality for enhanced productivity with CMT!

    TECHNICAL FEATURES:

    -Premium quality HWM.
    -2 spiral cutting edges (Z2).
    -Provide an excellent finish on the lower side of the workpiece.
    -Upward chip ejection.
    » View More

    From $39.00 (inc GST)
     
  • 191B Series Spiral Flush Trim Router Bits

    The new CMT solid carbide spiral flush trim bits are manufactured with a special super-micrograin formulation that has increased hardness with a higher transverse rupture point. Combined with the spiral cutting angle, the new CMT solid carbide spiral flush trim bits with double bearing allow the cabinet maker to sheer wood and wood products cleanly, providing more efficient chip ejection than standard flush trim bits. In production settings these new bits will run cooler and the edges will stay sharper, last longer and increase your shop productivity.

    » View More

    From $139.00 (inc GST)
     
  • 192 Series Solid Carbide Downcut Spiral Bits

    Sharp technology with a new twist

    A special super-micrograin carbide formulation was created to produce and hold a keen cutting edge. The new low-angle spiral is designed specifically to shear wood cleanly and provide efficient chip ejection. The tools run cooler and the edges last longer.

    Increased feed rate and improved cutting quality for enhanced productivity with CMT!

    TECHNICAL FEATURES:

    -Premium quality HWM.
    -2 spiral cutting edges (Z2).
    -Provide an excellent finish on the upper side of the workpiece.
    -Downward chip ejection.
    » View More

    From $39.00 (inc GST)
     
  • 800 Series 13 Piece Bit Set Suits Leigh Dovetail Jigs 80051911

    Perfect for the craftsman with a creative flair, these CMT’s sets contain the most frequently used bits for making boxes, creative joinery and a wide range of other projects. Safely packaged in a hardwood box to have the bits within a hand’s reach. The bits suit most popular jigs.

    IDEAL FOR LEIGH D4 JIGS.

    » View More

    $349.00 (inc GST)
     
  • 800 Series 3 Piece Divided Light Door Set 80052511

    Build authentic divided light doors for fine furniture and cabinets with these 3 piece sets. They include a stuck bit to cut the decorative ovolo profile on the frame edges, a cope to shape the mating profile on the ends of the stock, and a rabbeting bit to cut the recess for the glass. Thanks to the guide bearings, you can also create arched on curved frames. The unique design of the cope bit allows you to use full-length tenons to create strong, authentic mortise-and-tenon joinery. As the stock is coped, the tenon passes over the bit. These sets are designed for 22,2mm (7/8") wide bars such as those on corner cupboard door. Available in 8mm (5/16") and 12,7mm (1/2)" shanks. Instructions included.

    » View More

    $149.00 (inc GST)
    Out of Stock
     
  • 800 Series 3 Piece Entry & Interior Door Set 80052711

    This CMT three-piece router bit set simplifies door construction, making it easy as 1, 2, 3! It is not the only advantage, in fact this is a multifunctional set for door and furniture makers building entry or passage doors and any furniture tenons. The included tenon cutter produces a beefy 27mm (1-1/16”) long tenon. Coupled with the cope cutter, you can produce long and strong tenons with minimum setup. As an extra bonus the tenon cutter can be used for furniture making requiring any tenon from 4,7mm (3/16”) to 16mm (5/8”) thick.

    » View More

    $429.00 (inc GST)
    Out of Stock
     
  • 800 Series 3 Piece Kitchen Doormaking Sets

    Open new doors with CMT! Our 3 piece kitchen sets include a couple of rail and style bits and a raised panel bit. Choose among 4 possible profiles to make panel doors easy and economical. Each bit is made from bar stock steel and the highest quality tungsten carbide, along with the trademark orange non-stick PTFE coating. Also, they all come with their protective hardwood case: a very nice object to keep your bits safe, organized and within hand’s reach.
     
    » View More

    From $269.00 (inc GST)
     
  • 800 Series 3 Piece Small Arch Door Set 80052411

    These 3 piece sets will produce beautiful raised panel doors with a classic, diminutive bevelled profile. Designed for use in fine furniture making, these sets include two matched cope and stick bits for producing frames from 15,87mm (5/8”) to 19mm (3/4”) thick. The stick bit shapes a decorative 4,76mm (3/16”) thumbnail moulding along the edge of the frame. The panel bit is designed for 12,7mm (1/2”) think material. All bits are equipped with guide bearings for shaping curved work such as the small arched panel doors seen on secretaries and corner cabinetry. These sets also produce panels for small chests, lids for small boxes, or drawer fronts. Instructions included .

    » View More

    $199.00 (inc GST)
     
  • 800 Series 5 Piece Complete Kitchen Sets

    <p><span style="color: rgb(119, 119, 119); font-family: 'Trebuchet MS', Arial, Helvetica, sans-serif; font-size: small; text-align: justify;">These CMT&rsquo;s sets aren&rsquo;t only a random selection of odds and ends packaged in a nice elegant box, but they are also professional kits for drawer and door makers. 3 sets to choose from, 5 different bits to suit your needs: a raised panel bit, rail and stile bits, a glue joint and a drawer lock bit. Please refer to the illustrations below for complete profile options.</span></p> » View More

    From $399.00 (inc GST)
     
  • 800 Series 6 Piece Cabinetmaking Sets 80051511

    Available with raised panel bits in two different profiles, these sets feature six router bits for making arched raised panel doors and professional drawer fronts. These sets include:

    OGEE RAIL & STILE BITS: these two perfectly matched tools will eliminate the frustration of setting up reversible cutters. The stile bits also feature shear angles for neater cuts.

    RAISED PANEL BIT WITH BACKCUTTER: this 88,9mm (3-1/2") diametre bit features a backcutter for milling both the front and the back on the panel in a single cut. We recommend using a 31,7mm (1-1/4") diametre bearing to work safely in two shallow passes.

    SUPER-DUTY FLUSH TRIM BIT: this 19mm (3/4") diametre bit gives you a superior cut with minimal chipping, even on end grain.

    OGEE DOOR EDGE BIT: a subtle cove followed by a subtle roundover adds an elegant touch to your door edge.

    DRAWER FRONT BIT:: this bit makes a mini-raised panel cut on the outside edges of your drawer fronts.
     
    » View More

    $469.00 (inc GST)
     
  • 800 Series 8 Piece Bit Set Suits Incra Jigs 80050111

    Perfect for the craftsman with a creative flair, these CMT’s sets contain the most frequently used bits for boxes, creative joinery and a wide range of other projects. Safely packaged in a hardwood box to have the bits within a hand’s reach. The bits suit most popular jigs.

    IDEAL FOR INCRA & JOINTECH JIGS.

    » View More

    $309.00 (inc GST)
     
  • 800 Series Box Joint Router Bit 80061611

    This router allows you to carry out accurate and functional finger joints in a much easier way. Without any adjustment you will be able to work woods with different thicknesses as indicated in the drawing. The bearing allows you to reach a 9,5mm (3/8") cutting depth. For further cutting depths you need to use a fence.

    » View More

    $129.00 (inc GST)
     
  • 800 Series Finger Joint Router Bit 80060611

    Use these bits to make incredibly strong side-to-size or end-to-end joints in multiple wood kinds or composites. The tightness of the accurately cut joint and the maximum glue surface create a joint that is actually stronger than the wood itself. The bit features two flute design, carbide teeth and six removable cutters. Use them in combination to mill joints from 12,7mm (1/2”) to 36mm (1-3/8”).
     
    » View More

    $149.00 (inc GST)
     
  • 800 Series Stacked Slot Cutter Set 80050611

    Create slots, grooves and rabbets in materials from 3,2mm (1/8") to 18mm (23/32") in depth by using the adjustable CMT three wing slot cutter set. See chart below for details on spacing and correct cutter combinations. Ideal for biscuit joints and milling perfect tongue and groove joints. Sets include:
     
    - 4 carbide tipped cutters 3,2mm (1/8"), 4mm (5/32"), 4,8mm (3/16"), 6,4mm (1/4").
    - A 12mm (15/32") or 12,7mm (1/2") arbor.
    - A 22mm (7/8") ball bearing for a cutting depth up to 12,7mm (1/2").
    - 17 shims in different sizes.
     
    Shop tips: the 791.711.00 bearings kit allows for 6,35 (1/4") and 9,5mm (3/8") cutting depth.
     
     
     
    » View More

    $109.00 (inc GST)
     
  • 800 Series Tongue and Groove Deluxe Set 80052611

    CMT has developed a tongue and groove cabinet making system that derives from the superior traditional European methods of joinery. Combine the CMT tongue and groove system with the ease and speed of new world pocket hole methods and you have the versatility to build single cabinets or entire kitchens!
     
    The CMT Tongue and Groove Set includes a matched set that produce a 6,35mm x 6,35mm (1/4” x 1/4") tongue. The feature of the CMT system that sets it apart from other tongue and groove sets is that the tongue is offset to one side of the joint.
     
    This system produces a stronger joint allowing for more drilling area when used in conjunction with the CMT Pocket Pro when employing face frame screws. When the Pocket Pro is set at the one inch setting the screw will bypass the tongue and get a full bite in the grooved section, producing a much stronger joint.
     
    In some cabinet making applications, it is necessary to trim portions of the tongue. For this reason, we have included a 12,7mm (1/2") shank flush trim bit to complete the three piece set. The CMT tongue and groove joint is used in every element of joining, cabinets. When used in conjunction with the CMT Pocket Pro System you will be able to employ the best facets of traditional European joinery with new world methods for face frame joints and in completely concealed areas where bottoms, sides and dividers are attached to the face frame.
     
    The original CMT Tongue and Groove Cabinet Making System is manufactured in Italy. You can be assured that you are buying original CMT products by analyzing the shank of CMT router bits. All genuine CMT bits have the words, “Made in Italy” laser etched into the shank.
     
    » View More

    $179.00 (inc GST)
     
  • 800 Series Tongue and Groove Standard Set 80062611

    Make tongue and groove joints without the complicated process of taking apart and reassembling bits. The new CMT tongue and groove set gives you one bit to groove the slot and a separate bit to mill the tongue. Or use your imagination and put them to work individually on other projects. Makes tongue and groove cuts in wood up to 19mm (3/4") thick.

    » View More

    $109.00 (inc GST)
     
  • 801 Series Mortising Router Bits

    Equipped with thick carbide tips and negative shear angle design, CMT Mortising bits guarantee you a flawless performance. Mortise perfect hinges with no splintered edges or rough bottoms. They also make an easy job of piece work in both natural wood and wood composites. Fit most popular mortising jigs. The CMT mortising bit with top bearing guide is the perfect bit for sign making or any kind of template work.

    » View More

    From $27.00 (inc GST)
     
  • 801B Series Guided Mortising Router Bits

    Equipped with thick carbide tips and negative shear angle design, CMT Mortising bits guarantee you a flawless performance. Mortise perfect hinges with no splintered edges or rough bottoms. They also make an easy job of piece work in both natural wood and wood composites. Fit most popular mortising jigs. The CMT mortising bit with top bearing guide is the perfect bit for sign making or any kind of template work.
     
    801.128.11B is designed for Dado clean-out and is for flooring medallions.
     
    » View More

    From $37.00 (inc GST)
     
  • 806 Series Flush Trim Router Bits

    We have designed a series of truly indispensable bits available in a wide range of sizes for your woodworking needs and your most difficult projects. For precision work on laminates or quick template work with excellent finishing.

    Shop tips: these bits are excellent for making through mortise. Use a straight bit (711.130.11) to groove the area to make the through mortise. With a drill bit (517.130.31) bore a hole through the wood at one end of the groove. Turn the workpiece over to finish the mortise. Use a flush trim bit with a cutting length slightly longer than the fillet, following the groove made on the opposite side of the workpiece with the ball bearing guide.

     
    » View More

    From $119.00 (inc GST)
     
  • 807 Series 3-In-1 MDF/Laminate Flush Trim Bits

    3 in 1 new flush trim bits with Delrin® triangular bearings are your best partner for laminate trimming. In fact they solve 3 of the most common problems that occur in flush trimming in cabinet shops. 

    1) The anti-stick properties of the Delrin® bearing greatly reduces the likelihood of freezing of the bearing from glue. 
    2) The extended guide surface of the new Delrin® bearing will perfectly match the work surface without scratching like the steel bearing would. The Delrin® bearing also guarantees maximum stability. 
    3) The shear angle cutting edge reduces the need for filing. 3 in 1 bits are ideal on plastic laminates as well as aluminium laminates! 

    3-in-1 bits are ideal on plastic laminates, as well as on aluminium laminates! 

    Bearing is patented. Patent no. D628,218. 
    -Extended guide surface.
    -Non-freezing.
    -Non-scratch surface.

    » View More

    From $42.00 (inc GST)
     
  • 811 Series Short Straight Router Bits

    If you are looking to get the most out of your time and money through more efficient production, but want nothing less than a beautiful clean edge on your finished piece, then you definitely must include CMT straight bits in your collection. These razor-sharp, double-faced cutters perfectly synthesize the characteristics and advantages that define quality CMT products. Made of special Fatigue Proof® steel and micrograin carbide, our straight bits can withstand even the heaviest work load and still give you a smooth, precise cut every time. You also get exceptional chip ejection to allow cleaner and more constant cutting. The surface of all CMT bits is protected with our trademark orange non-stick PTFE to help keep the bit from collecting resin, pitch and other residue. Every bit is submitted to strict quality tests to guarantee perfect cutting tolerance, balance and concentricity. CMT bits allow production on an industrial scale using a variety of plywood, composites and natural woods.

    » View More

    From $32.00 (inc GST)
     
  • 811B Series Pattern Following Router Bits

    Whether you are a full time professional or a part time woodworking enthusiast, discover the unlimited possibilities of template routing with a CMT pattern bit. Pair up these double fluted bits with your choice of template to produce cabinet and furniture pieces, signs, toys and any other creative projects. Carbide tipped to last longer, CMT pattern bits are equipped with top bearing for working with the bearing above the wood piece. This gives you a clear view of what you are routing so you can work confidently and accurately.

    811.081.11B requires a slightly larger bearing than its cutting diameter.

     
    » View More

    From $59.00 (inc GST)
     
  • 812 Series Long Straight Router Bits

    If you are looking to get the most out of your time and money through more efficient production, but want nothing less than a beautiful clean edge on your finished piece, then you definitely must include CMT straight bits in your collection. These razor-sharp, double-faced cutters perfectly synthesize the characteristics and advantages that define quality CMT products. Made of special Fatigue Proof® steel and micrograin carbide, our straight bits can withstand even the heaviest work load and still give you a smooth, precise cut every time. You also get exceptional chip ejection to allow cleaner and more constant cutting. The surface of all CMT bits is protected with our trademark orange non-stick PTFE to help keep the bit from collecting resin, pitch and other residue. Every bit is submitted to strict quality tests to guarantee perfect cutting tolerance, balance and concentricity. CMT bits allow production on an industrial scale using a variety of plywood, composites and natural woods.

     

    » View More

    From $36.00 (inc GST)
     
  • 813 Series Counterbored Screw Slot Router Bits

    Any large panel or table top should be secured in a way that allows it to expand or contract without splitting. These screw-slot bits let you create screw slots so that panels can be held in place but are able to slide back and forth without splitting the wood or breaking the screw securing them.
     
    » View More

    From $59.00 (inc GST)
     
  • 813 Series Weatherseal Router Bits 81300111

    Make your house more energy efficient by insulating old doors and windows. A CMT Weatherseal bit is the perfect bit to re-groove door and window frames to accommodate wind blocking inserts. Made of solid carbide for strength and endurance. Special economical double-sided design lets you save money by offering two tips in one bit; with the same features as the one-sided weatherseal bit. Only available with a 3,5mm (9/64”) cutting diameter.

    » View More

    $59.00 (inc GST)
     
  • 814 Series Round Nose Router Bits

    Personalize your doors, drawer fronts, panels or any surface you choose with your own signature motif. CMT round nose bits in solid carbide or with carbide tipped flutes let you create engraving in any wood or wood product. We offer a complete selection of diameters and cutting depths so you can achieve the effects you want. Mounted on your router table, you can work materials up to 31,7mm in depth. For even more elaborate decorations, we also offer top bearing bits - use your own template with one of these bits to produce truly unique doors and drawer fronts. A favorite item for professional sign makers, craft makers and hobbyists.
     
    Shop tips: more than one pass is recommended when making cove edges. To prevent splintering, begin with a shallow initial pass and deepen gradually.
     
    » View More

    From $37.00 (inc GST)
     
  • 814B Series Guided Round Nose Router Bits

    Personalize your doors, drawer fronts, panels or any surface you choose with your own signature motif. CMT round nose bits in solid carbide or with carbide tipped flutes let you create engraving in any wood or wood product. We offer a complete selection of diameters and cutting depths so you can achieve the effects you want. Mounted on your router table, you can work materials up to 31,7mm in depth. For even more elaborate decorations, we also offer top bearing bits - use your own template with one of these bits to produce truly unique doors and drawer fronts. A favorite item for professional sign makers, craft makers and hobbyists.

    Shop tips: more than one pass is recommended when making cove edges. To prevent splintering, begin with a shallow initial pass and deepen gradually.

    » View More

    From $46.00 (inc GST)
     
  • 815 Series V-Grooving Router Bits

    These double cutting edge CMT bits offer an almost endless range of woodworking possibilities. Make clean, perfect cuts in panels, drawer fronts or even plasterboard panels; chamfer edges or engrave beautiful lettering. Like all CMT bits, they are made of super strength Fatigue Proof® steel with carbide-tipped cutting edges and are coated with our trademark orange PTFE non-stick coating. These bits are ideal for routing signs, or almost any project that is suitable for accurate template routing.
     
    Tips: V-grooving bits can perfectly chamfer 45°.
     
    Items featuring 31,7mm (1-1/4”) cutting diameters are suitable for plasterboard.
     
    » View More

    From $35.00 (inc GST)
     
  • 815B Series Guided V-Grooving Router Bits

    These double cutting edge CMT bits offer an almost endless range of woodworking possibilities. Make clean, perfect cuts in panels, drawer fronts or even plasterboard panels; chamfer edges or engrave beautiful lettering. Top bearing allows for several template options. Like all CMT bits, they are made of super strength Fatigue Proof® steel with carbide-tipped cutting edges and are coated with our trademark orange PTFE non-stick coating. These bits are ideal for routing signs, or almost any project that is suitable for accurate template routing.

    Tips: V-grooving bits can perfectly chamfer 45°. Two tools in one!

     
    » View More

    From $44.00 (inc GST)
     
  • 816 Series Panel Pilot Router Bits

    How long do you spend making openings in paneling, drywall, siding, doors or windows? With the CMT panel pilot bit, the job just got quicker. The point plunges smoothly and easily and the carbide edges cut clean and fast. All of this adds up to accurate cuts in less time and with less effort - great for trimming Formica®, veneer and other laminates.

    » View More

    From $28.00 (inc GST)
     
  • 818 Series Dovetail Router Bits

    The beautifully crafted dovetail joint is a classic that appeals to both professionals and novices alike. Admired for its attractiveness in box and exposed joint projects, the dovetail is remarkably strong and functional. CMT dovetail bits are designed to fit all popular jigs including Leigh, Keller, JoinTECH and Omnijig systems. You are sure to find the bit you are looking for in our vast selection of cutting sizes and angles. Check the overall length of the bit before placing an order to be sure you get the size you need - CMT makes bits specifically to fit on jigs and routers that require a longer shank length.

     

    » View More

    From $38.00 (inc GST)
     
  • 821 Series Combination Trimmer Bits

    Work to your highest standards with the CMT combination trimmer bits. Now you can cut, trim and bevel all laminated without changing the bits. Achieve great results in straight or angled cuts on both soft and hardwood. Three popular sizes, each with carbide-tipped cutting edges for efficient bevel and straight trimming.

    Notice: these bits must be used with and edge, separate guide or fence.

    » View More

    From $32.00 (inc GST)
     
  • 822 Series Slot Cutter Assemblies

    Uses for the CMT three wing slot cutter are almost infinite. Cut slots and grooves for splines, biscuits, T-molding or tongue and groove joints. Every cutter features anti-kickback design, micrograin carbide tips and orange CMT trademark non-stick PTFE coating. CMT slot cutters are available as a blade only or with your choice of many arbors which include a 22mm (7/8") diameter bearing for a cutting depth of up to 12,7mm (1/2").

    Notice: for biscuit joints, use slot cutter with 4mm (5/32”) cutting length.

     
    » View More

    From $49.00 (inc GST)
     
  • 822 Series Slot Cutters

    &lt;div id=&quot;tabs&quot; style=&quot;padding: 0px 0px 0px 14px; margin: 0px; border: 0px; background-image: url(http://www.cmtutensili.com/img/tab_bg_sx.gif); background-attachment: scroll; color: rgb(119, 119, 119); font-family: &#39;Trebuchet MS&#39;, Arial, Helvetica, sans-serif; background-position: 0% 0%; background-repeat: no-repeat repeat;&quot;&gt; &lt;div id=&quot;tabs_2&quot; style=&quot;padding: 0px 14px 0px 0px; margin: 0px; border: 0px; background-image: url(http://www.cmtutensili.com/img/tab_bg_dx.gif); background-position: 100% 0%; background-repeat: no-repeat repeat;&quot;&gt; &lt;div align=&quot;justify&quot; style=&quot;padding: 0px; margin: 0px; border: 0px;&quot;&gt;&lt;font size=&quot;2&quot; style=&quot;padding: 0px; margin: 0px; border: 0px;&quot;&gt;Slot cutters for sidelong grooves. They feature 8mm (5/16&amp;quot;) bore diameters, 47,6mm (1-7/8&amp;quot;) cutting diameters and cutting length from 1,6mm (1/16&amp;quot;) to 6,4mm (1/4&amp;quot;).&lt;/font&gt;&lt;/div&gt; &lt;div&gt;&amp;nbsp;&lt;/div&gt; &lt;/div&gt; &lt;/div&gt; » View More

    From $29.00 (inc GST)
     
  • 823 Series Deluxe Slot Cutter Set 82300111

    Create slots, grooves and rabbets easily with these CMT slot cutters sets. Ideal for biscuit joints and milling perfect tongue-and-groove joints, these sets include 4 bearings allowing different cutting depths: 7,95mm (5/16”), 9,55mm (3/8”), 12,7mm (1/2”) and 14,3mm (9/16”). Please refer to the drawings for some application examples and the correct cutter combinations.

    » View More

    $359.00 (inc GST)
     
  • 823 Series Slot Cutters

    These wing carbide tipped slot cutters feature anti-kickback three wing blade design and CMT’s trademark orange PTFE Industrial Coating. All cutters feature an 8mm (5/16") bore that fits CMT’s arbors (items 7/8/924).
     
    » View More

    From $32.00 (inc GST)
     
  • 824 Series Arbors For Slot Cutters

    D= M8mm (5/16") L1= 26mm (1-1/32")

    » View More

    From $18.00 (inc GST)
     
  • 827 Series Ovolo Router Bits

    CMT put the work capacity of several different bits all into one. The perfect bit for furniture makers, the CMT ovolo allows you to make beautiful beadwork, edgework and veins. Use these bits on automated router systems or with a fence to produce a wide variety of single and double bead profiles and roundovers like those illustrated below by simply adjusting the height or depth of the cut.

    » View More

    From $42.00 (inc GST)
     
  • 835 Series Rabbeting Router Bit Sets

    These rabbeting sets allow you to make an endless number of cuts by adjusting the cutting height on your router and changing the bearing on the bit.

    Be sure to keep the black bearing washer right side up to correspond with the bearing rotation when reassembling the bearing. Improper reassembly can cause the screw to come loose. Each set comes complete with one rabbeting bit and six interchangeable ball bearing guides.

    » View More

    From $109.00 (inc GST)
     
  • 835 Series Rabbeting Router Bits

    CMT carbide-brazed rabbeting bits are fast and accurate. You can quickly produce inset doors and drawer fronts, make strong rabbet joints, mill perfect tongue and groove joints or any number of other jobs that before were time consuming and difficult. You can even re-groove old window frames to fit insulated glass panes with the extra-long CMT 19mm (3/4“) rabbeting bit. Other possibilities are illustrated below and on the following pages. Look at our slot cutters and round over bits for ideas on how to put extra finishing touches on all your grooving and rabbeting projects.
     
    » View More

    From $49.00 (inc GST)
     
  • 835 Series The CMT Grand Rabbet Set 83550311

    The ultimate rabbeting sets & the ultimate tool value. These sets include our 835.990.11 bit with 22mm (7/8”) cutting height, plus bearings to cut 17 different rabbets, all in a sturdy molded case. For rabbet sizes over 12,7mm (1/2”) we suggest cutting in several shallow passes to achieve the desired cutting depth. Available in 12mm (15/32”) and 12,7mm (1/2) shanks.
     
    » View More

    $249.00 (inc GST)
     
  • 836 Series Chamfer Router Bits

    CMT chamfer bits can cut clean, accurate bevels and chamfers and are great for edge work or for making perfectly aligned multi-sided containers, boxes and other decorative projects. See illustration below for examples. Can be used for working larger scale projects such as beams and columns with excellent results.

    » View More

    From $41.00 (inc GST)
     
  • 837 Series 3 Piece Cove Router Bit Set 83750111

    This set includes carbide cove bits in three of the most commonly-used sizes. You will get 12,7mm (1/2”) radius bits.

    » View More

    $159.00 (inc GST)
     
  • 837 Series Cove Router Bits

    Make simple or elegant furniture, doors and drawer fonts by adding a final touch with CMT cove bits. Join them together with a CMT roundover bit and make perfectly fitting rule joints, ideal for drop leaf counter and table tops. These bits feature anti-kickback design, carbide-tipped cutting edges, Fatigue Proof® steel body and PTFE non-stick coating.

    » View More

    From $45.00 (inc GST)
     
  • 838 Series 3 Piece Roundover Bit Set 83850111

    CMT’s roundover sets give you the maximum flexibility for all of your projects by putting the most requested diameters in one package. Available in 12,7mm (1/2") . Roundover radii are 6,35mm (1/4"), 9,5mm (3/8") and 12,7mm (1/2"). These versatile bits are always in demand - the simple clean lines of a smooth roundover edge can be used in a wide variety of applications from picture frames to table and counter tops.
     
    » View More

    $169.00 (inc GST)
    Out of Stock
     
  • 838 Series Roundover Router Bits

    The smaller bearing on the CMT Beading bits makes a delicate inset at the base of the cut, giving you the advantage of an extra decorative option. Be sure to keep the black bearing washer right side up to correspond with the bearing rotation when reassembling the bearing. Improper reassembly can cause the bit to unscrew. All CMT roundover bits have a 12,7mm (1/2") bearing diameter with the exception of the radius 28,6mm (1-1/8") and 31,7mm (1/4") bits which have a 19mm (3/4") bearing diameter. You have 13 different radii to choose from, the majority having 5 shank diameter options. All bits are made of Fatigue Proof® steel and have carbide-tipped cutting edges.

    » View More

    From $44.00 (inc GST)
     
  • 839 Series Beading Router Bits

    Beading bits are similar to the roundover profile, but a smaller bearing produces a delicate inset at the base of the cut, giving you an extra decorative option. For a beading profile (code 7/8/939) simply change the bearing (791.002.00) on your roundover bits (code 7/8/938).
     
    Bits featuring 25,4mm (1") radius are to be used only on router table.
     
    » View More

    From $47.00 (inc GST)
     
  • 840 Series Roman Ogee Router Bits

    The roman ogee may be the most popular edge treatment in woodworking, and it is certainly one of the most beautiful. This bit includes all CMT bit features and produces a perfect rendition of classic design.

    Shop tips: for best results, multiple passes are recommended.

    » View More

    From $59.00 (inc GST)
     
  • 841 Series Roman Ogee Router Bits

    This bit takes the Roman ogee a step further. The horizontal bead adds style and elegance to the traditional shape.
     
    Shop tips: for best results, multiple passes are recommended.
     
    » View More

    From $69.00 (inc GST)
     
  • 842 Series Combination Trimmer Router Bits

    Work to your highest standards with the CMT combination trimmer bits. Now you can cut, trim and bevel all laminated without changing the bits. Achieve great results in straight or angled cuts on both soft and hardwood. Three popular sizes, each with carbide-tipped cutting edges for efficient bevel and straight trimming.

    Notice: these bits must be used with and edge, separate guide or fence.

    » View More

    From $21.00 (inc GST)
     
  • 844 Series Classical Ogee Router Bits

    CMT’s classical ogee bits feature an inverted ogee profile, with the concave edge adjacent to the upper surface of the workpiece. A vertical bead was added to separate the curves and creates an eye-catching shape.

    Ship tips: for best results, multiple passes are recommended.

    » View More

    From $69.00 (inc GST)
     
  • 845 Series Classical Ogee Router Bits

    CMT’s classical ogee bits feature an inverted ogee profile, with the concave edge adjacent to the upper surface of the workpiece. A vertical bead was added to separate the curves and creates an eye-catching shape.

    Shop tips: for best results, multiple passes are recommended.

    » View More

    From $69.00 (inc GST)
     
  • 846 Series Ogee With Fillet Router Bits

    Take a complete assortment of CMT ogee bits into your shop. These bits feature micrograin carbide edges, high strength steel and the trademarked orange non-stick PTFE coating.
     
    Shop tips: for best results, multiple passes are recommended.
     
    » View More

    From $69.00 (inc GST)
     
  • 847 Series Ogee With Fillet Router Bits

    For a more-detailed profile, this bit adds an inset bead along the lower edge of the cut.

    Shop tips: for best results, multiple passes are recommended.

    » View More

    From $69.00 (inc GST)
     
  • 848 Series Plunge Ogee Router Bits

    For a more-detailed profile, this bit adds an inset bead along the lower edge of the cut.
     
    Shop tips: for best results, multiple passes are recommended.
     
    » View More

    From $59.00 (inc GST)
     
  • 848B Series Guided Plunge Ogee Router Bits

    For more CMT ogee profile options, choose among plunge ogee bits with top bearing. Excellent for achieving accurate decorative work and guaranteed for long lasting performance.

     

    » View More

    From $69.00 (inc GST)
     
  • 849 Series Lettering Router Bits

    The ideal bit for routing signs. CMT has designed a bit with a 60° curved profile, a 3,2mm (1/8“) radius and a flattened bottom to make relief letter-making easy and accurate. This exclusive design allows you to efficiently level off the area around the base of the letter and bevel the letter edges to eliminate aggravating splintering.

    » View More

    From $59.00 (inc GST)
     
  • 849B Series guided Lettering Router Bits 84950111-B

    The ideal bit for routing signs. CMT has designed a bit with a 60° curved profile, a 3,2mm (1/8”) radius and a flattened bottom to make relief letter-making easy and accurate. This exclusive design allows you to efficiently level off the area around the base of the letter and bevel the letter edges to eliminate aggravating splintering. The top bearing guide allows for even more precise decorative effects.

     
    » View More

    $69.00 (inc GST)
     
  • 850 Series Keyhole Router Bits

    With the CMT keyhole bit you can make holes that keep your frames, plaques or any wall hanging perfectly straight and attached to the wall. The bit bores an entry hole in the wood, then proceeds to cut a 4,8mm (3/16") hole and finishes by boring a larger opening under the surface. The perfect way to securely mount wall hangings on screws and nails.
     
    Shop tips: recommended for use with a plunge router.
     
    » View More

    From $46.00 (inc GST)
     
  • 850 Series T-slot Router Bits

    With the CMT T-slot bits you can make holes that keep your frames, plaques or any wall hanging perfectly straight and attached to the wall. These bits bore an entry hole in the wood, then proceed to cut holes and finished by boring a larger opening under the surface. The perfect way to securely mount wall hangings on screws and nails.
     
    Shop tips: recommended for use with a plunge router.
     
    » View More

    From $79.00 (inc GST)
     
  • 851 Series Bowl & Tray Router Bits

    This CMT bit is ideal for making bowls, trays, boxes, cutting boards or any other specialty or craft item. The round corner of the bit shapes the inner radius while the sides and bottom create the smooth flat surfaces. Makes pattern work quick and easy..
     
    » View More

    From $49.00 (inc GST)
     
  • 851B Series Guided Bowl And Tray Router Bits

    This CMT bit is ideal for making bowls, trays, boxes, cutting boards or any other specialty or craft item. The round corner of the bit shapes the inner radius while the sides and bottom create the smooth flat surfaces. Makes pattern work quick and easy. Bowl and tray bits with top bearings are great for pattern work. Use them to create raised sign lettering, trays and many other items.
    » View More

    From $69.00 (inc GST)
     
  • 853 Series Flush & V-groove Router Bits

    An absolutely indispensable bit for making cabinets. CMT Flush and V-Groove bits allow you to make cabinet front frames in 25mm (1") stock that fit perfectly with the sides. The added V-cutter feature makes a decorative groove along the hinge joint to hide the seam.
     
    Shop tips: for best results, leave less than 3mm (1/8") overhang on cabinet front frames for easier routing.
     
    » View More

    From $59.00 (inc GST)
     
  • 854 Series Bead & Bull Nose Router Bits

    CMT bull nose bits create beautifully finished edges on stair treads, window sills and shelves in a pass. Ad a final touch by using a cutter with a bead diameter wider than the stock thickness. CMT bull nose bits have bead diameters from 6,35mm (1/4”) to 25,4mm (1”) and each bit features carbide-tipped cutting edges, anti-kickback design and the orange PTFE non-stick coating trademark.
     
    » View More

    From $47.00 (inc GST)
     
  • 855 Series 3 Piece Glass Panel Bit Set 85580311

    CMT’s unique stile and rail router bit sets allow you to produce glass panel doors by using a rubber panel retain to secure the glass in a 3,2mm (1/8") slot cut into the frames. These bits work the same as other CMT’s stile and rail sets, but they leave you with a square rabbet on the inside of your door for installing the glass panel. Available in 12mm (15/32") and 12,7mm (1/2") shanks.
     
    Our unique retainer strips fit perfectly in the slots created by the slot cutter bit and hold your glass securely in the frame. Sold in 762cm (25') lengths.
    » View More

    $239.00 (inc GST)
     
  • 855 Series Drawer Lock Router Bits

    The key to success when constructing quality drawers is in the quality of the drawer lock bit you use. With CMT drawer lock bits you can make strong, perfectly fitting joints quickly and easily. Mill the drawer front with the inside face-down on the work table. Mill the sides of the drawer with the inside face placed vertical to the bit and fence, and perpendicular to the table.
     
    » View More

    From $59.00 (inc GST)
     
  • 855 Series Edge Banding Router Bit Set 85551011

    This is a great set to create economical but attractive and durable edge to your cabinet doors. Use 12,7mm (1/2”) or 25,4mm (1”) thick panels in plywood or MDF and create your own edge banding from the wood of your choice. Easy to use: just center each cutter on the stock and make the cut; glue together the two pieces and flush trim it after assembly if necessary. The set features a 60° tongue & groove for a large surface area for glue.
     
    » View More

    $179.00 (inc GST)
     
  • 855 Series Finger Pull Router Bits

    Why interrupt the subtle linearity of an all-wood drawer front or cabinet door with a metal knob or handle? Use a CMT finger pull bit and make a harmonious wooden handle. Choose your preference - a template profile made directly in the wood or a European-style hardwood pull.

    » View More

    From $109.00 (inc GST)
     
  • 855 Series Flute & Bead Router Bit Set 85570111

    This perfectly mated CMT set is ideal for making canoe slats and hot tubs. Featuring tungsten carbide, the bits’ cutting edges stay sharp after cutting large amounts of stock, and the anti-kickback design lets you work safely. Set includes 2 bits. Use both the flute and the bead bits for 6,35mm (1/4”) slats.
     
    » View More

    $139.00 (inc GST)
     
  • 855 Series Lock Mitre Router Bit Set 85550511

    Now you don’t have to fight with those awkward clamps on your 22,5º projects. Use this pair of bits to produce octagonal shaped boxes and popular corner cabinetry like corner cabinets for kitchens, entertainment centres, kitchen islands and corner hutches. This 22,5º Lock Miter set provides a strong tight joint when you want to join wood at 45º angles. Biscuits and splines are time-consuming to make and difficult to clamp. CMT’s matched pair of cutters makes set-up easy. Height adjustment is not critical with this matched pair; simply adjust your fence so the top edge of the work piece intersects the angle of the bit where it meets the fence. After your joints are machined they can be glued and assembled and simply clamped by using strapping tape.
     
    » View More

    $189.00 (inc GST)
     
  • 855 Series Lock Mitre Router Bits

    CMT lock miter bits are ideal for milling miter joints from 9,5mm (3/8") to 28,5mm (1-1/8") stock. The quick and easy way to accurately create boxes, stretcher bars, frames and any assortment of right angle or parallel joint projects.

    » View More

    From $159.00 (inc GST)
     
  • 855 Series Moulding Router Bits

    Why waste time searching for a particular style of frame molding when you can just as quickly and easily make your own. With the wide range of decorative possibilities offered by CMT molding bits, you can always create the edge profile you want, anywhere you want and any time you want. These CMT bits are made to last a lifetime - carbide-tipped cutters and solid bar stock steel shanks can withstand serious use and the baked-on non-stick PTFE coating makes sure you continuously get clean, smooth-running cuts. Our anti-kickback feature helps guarantee you work more safely when using these wide profile bits.

    Shop tips: multiple pass operations require advance planning. To avoid making a mistake that could render it impossible to finish the job, carefully consider the entire cutting sequence before you begin.

    » View More

    From $99.00 (inc GST)
     
  • 855 Series Ovolo Sash Router Bits

    These bits allow you to make true divided light doors for fine furniture and cabinets as well as sash bar windows, and stile and rail constructions. The glazing bar ovolo bits are bearing-guided to enable curved frames to be moulded. Cove bits can be used to produce easy-to-pull drawer handles.

    » View More

    From $69.00 (inc GST)
     
  • 855 Series Reverse Glue Joint Router Bits 85550111

    The most unique and important characteristic of this CMT bit is its capacity to produce an almost indestructible glue joint quickly and without error. Ideal for routing wide dimension panels, doors and furniture pieces. By accurately centering the bit to the wood, the upper and lower vertical cutting edges of the bit will cut equal proportions. Simply run one edge of the panel, turn the panel over, and then run the opposite edge - you will produce perfectly harmonized reverse cuts that match up to make flawless joints.
     
    Shop tips: when gluing, apply enough pressure to securely seal the joint. Insufficient pressure results in a weak joint and excessive pressure will distort the wood.
     
    » View More

    $109.00 (inc GST)
     
  • 855 Series V-Tongue & Groove Router Bit Set 85550611

    If the standard selection of molding and mill work you find in today’s lumber shops isn’t satisfactory to your woodworking tastes, then look to CMT’s molding system instead. With these bits, you can make dozens of elaborate profiles by combining two or more passes. Avoid the average and create your own moldings.
     
    » View More

    $239.00 (inc GST)
    Out of Stock
     
  • 855 Series Window Sash Router Bit Set 85580111

    $199.00 (inc GST)
     
  • 855 Series Window Sill & Finger Pull Router Bits

    Originally intended for shaping window sill edges, these bits are also used for creating finger pulls on your door and drawer edges.
     
     
    » View More

    From $89.00 (inc GST)
     
  • 855B Series Guided Window Still & Finger Pull Router Bits

    Originally intended for shaping window sill edges, these bits are also used for creating finger pulls on your door and drawer edges. These bits are also available with a bearing for curved template work and straight cuts against the fence.

    » View More

    From $119.00 (inc GST)
     
  • 856 Series CMT Molding System

    If the standard selection of molding and mill work you find in today’s lumber shops isn’t satisfactory to your woodworking tastes, then look to CMT’s molding system instead. With these bits, you can make dozens of elaborate profiles by combining two or more passes. Avoid the average and create your own moldings.
     
    » View More

    From $79.00 (inc GST)
     
  • 856 Series Multiprofile Router Bits

    Create endless profiles with CMT multiprofile bits. Simply adjust the height of the bit to create classic profiles in one single pass, or make more complex decorative effects in multiple passes. The bits super-strength steel body can withstand long-lasting cutting operations, and the micrograin carbide tips remain sharp longer for superior performance. In addition these bits feature baked-on non-stick PTFE coating and anti-kickback design. To be used on tables equipped with a fence.
     
    » View More

    From $109.00 (inc GST)
     
  • 856 Series Table Edge And Hand Rail Router Bits

    <p><span style="color: rgb(119, 119, 119); font-family: 'Trebuchet MS', Arial, Helvetica, sans-serif; font-size: small; text-align: justify;">Turn a small investment into a big return with these CMT bits! They give you well-proportioned smooth curves for elegant eye-catchy work on your tables. CMT hand rail bits feature 30&deg; bevel edge and 3,2mm (1/8&quot;) bead that allow you to make beautiful and functional hand rails. Add a touch of class to your architectural settings!</span></p> » View More

    From $129.00 (inc GST)
     
  • 857 Series Chamfer Router Bits

    CMT chamfer bits can cut clean, accurate bevels and chamfers and are great for edge work or for making perfectly aligned multi-sided containers, boxes and other decorative projects. See illustration below for examples. Can be used for working larger scale projects such as beams and columns with excellent results.

    » View More

    From $69.00 (inc GST)
     
  • 858 Series Laser Point Router Bit 85800111

    The 3-flute bits make delicate grooves and incisions with laser precision. Make kind effects by running the 60° bevel edges. Perfectly balanced to give you a superior accuracy with no risk or burning. Raise them to produce a delicate fine incisions or work the whole 12,7mm (1/2") diameter to render bold highlighted lettering. Super strong steel shank and micrograin carbide cutting edges guarantee long-lasting performance.

     
    » View More

    $46.00 (inc GST)
    Out of Stock
     
  • 859 Series Ogee Router Bits

    These profiles are the mirror image of the traditional roman ogee. They add a sharp defining details to the edges of cabinets and furniture, before rolling into a smooth convex shape. Series 859 bits can be converted to series 860 by changing the bearing to 3/8in, series 860 can be converted to series 859 by changing the bearing to 1/2in.
     
    Shop tips: for best results, multiple passes are recommended.
     
    » View More

    From $59.00 (inc GST)
     
  • 861 Series Corner Beading Router Bits

    Make beautiful traditional beads and edge beads or turn old beads into new moldings with the new CMT corner beading bits with bearing. Featuring carbide-tipped cutting edges and orange PTFE non-stick coating, these bits provide excellent results on corner beads. Run the bead twice to form a complete corner bead.
     
    » View More

    From $59.00 (inc GST)
     
  • 861 Series Wainscot/Paneling Router Bits 86160111

    This new router bit designed for 19mm (3/4”) thick stock is perfect for creating wainscots and panels on your walls. Simply create a 6,35mm (1/4”) tongue-and-groove interlock with a CMT 8/900.626.11, then, with two passes mill an attractive traditional beadboard profile with this new bit. Perfect for cabinets, bookcase backings, ceiling and wall paneling.

     
    » View More

    $69.00 (inc GST)
     
  • 863 Series Cavetto Edge Mold Router Bits

    <div id="tabs" style="padding: 0px 0px 0px 14px; margin: 0px; border: 0px; background-image: url(http://www.cmtutensili.com/img/tab_bg_sx.gif); background-attachment: scroll; color: rgb(119, 119, 119); font-family: 'Trebuchet MS', Arial, Helvetica, sans-serif; background-position: 0% 0%; background-repeat: no-repeat repeat;"> <div id="tabs_2" style="padding: 0px 14px 0px 0px; margin: 0px; border: 0px; background-image: url(http://www.cmtutensili.com/img/tab_bg_dx.gif); background-position: 100% 0%; background-repeat: no-repeat repeat;"> <div align="justify" style="padding: 0px; margin: 0px; border: 0px;"> <div>The&nbsp;cavetto&nbsp;bit cuts beautiful, traditional profiles, but you may also use just a portion of the bit to cut a more simple and cleaner cove edge. This bit add a special touch to furniture pieces by making traditional cove profiles with top and bottom&nbsp;fillet&nbsp;grooves in any kind of wood and wood composites.</div> &nbsp; <div>Important:&nbsp;always assemble the black bearing heat shield with the raised side up when changing the bearing. Improper assembly will cause the screw to come loose and the bearing to fall off when routing.</div> </div> </div> </div> » View More

    From $59.00 (inc GST)
     
  • 865 Series Classical Bead Router Bits

    This bit gives you even more decorative possibilities for panel and edge work. The bit design gives a wide flat bottom cut and a longer shank allows for a greater depth in the detail of the profile.
     
    » View More

    From $69.00 (inc GST)
     
  • 865 Series Decorative Ogee Router Bits

    This new CMT bit produces a classic single or double edged bead. Ideal for creating a marked decorative effect on panel, door and drawer work.

    » View More

    From $59.00 (inc GST)
     
  • 866 Series Solid Surface Rounding Over Bowl Router Bits 86660211

    These bits roundover and trim the countertop edges after the bowl is mounted. Can be used with the CMT 880.551.11 bevel cutter for a flush cut-out between the countertop and installed undermount bowl. For use on hand-held portable routers. Features a non-marring Delrin® bearing to protect the finished edges. Special angled Delrin® sleeve on the bearing of the CMT bevel cutter lets you work without leaving marks on the workpiece. Trims and shapes all wood and wood materials. Perfect for kitchen and bathroom counter top work.
    » View More

    $129.00 (inc GST)
     
  • 870 Series Panel Router Bits

    These bits can be used for decorative work on solid wood panels and MDF materials. Use them in one pass or in combination with CMT’s MDF panel bits for complex and intricate profiles. A simple approach for an elegant appearance. Featuring large cutting diameters and available in the most popular profiles, these panel bits guarantee excellent performance on both solid wood panels and MDF materials.
    » View More

    From $99.00 (inc GST)
     
  • 870 Series Stile Router Bits

    These bits can be used for decorative work on solid wood panels and MDF materials.
    » View More

    From $49.00 (inc GST)
     
  • 880 Series Solid Surface Bevel Bowl Bits 88055111

    These bits are designed for undermount applications joining the countertops and sink bowls with a 10 (degree) beveled edge. Can be used with the 880.541.11 and 880.542.11 for complete undermount applications. For use on hand-held routers. Features a non-marring Delrin® bearing to protect the finished edges.

    Special angled Delrin® sleeve on the bearing of the CMT bevel cutter lets you work without leaving marks on the workpiece. Trims and shapes all wood and wood materials. Perfect for kitchen and bathroom counter top work.

     
    » View More

    $99.00 (inc GST)
     
  • 880 Series Solid Surface Decorative Edge Profile Router Bits 88052111

    Create elegant countertops with flawless results. Features a non-marring Delrin® bearing to protect the finished edges. For use on hand-held portable routers.

    » View More

    $159.00 (inc GST)
     
Results 1 - 96 of 110 Show: Sort By: